43-1051.fm Page 1 Tuesday, August 17, 1999 1:08 PM
Cat. No. 43-1051
OWNER’S MANUAL
Please read before using this equipment.
ET-551
25-Channel
Cordless Phone
with 10-Number Memory
43-1051.fm Page 3 Tuesday, August 17, 1999 1:08 PM
Important Note: Cordless phones
such as this one require AC power to
operate. When the AC power is off,
you cannot dial out or receive incoming
calls using your ET-551. To be safe,
you should also have a phone that
does not need AC power to operate
(not a cordless phone) so you can still
make and receive calls if there is an
AC power failure.
READ THIS BEFORE
INSTALLATION
Each device that you connect to the
phone line draws power from the
phone line. We refer to this power draw
as the device’s ringer equivalence
number, or REN. The REN is shown
on the bottom of the base.
If you are using more than one phone
or other device on the line, add up all
the RENs. If the total is more than five,
your phones might not ring. In rural ar-
eas, a total REN of three might impair
ringer operation. If ringer operation is
impaired, remove a device from the
line.
WARNING: To reduce the risk of
fire or shock hazard, do not ex-
pose this product to rain or mois-
ture.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
FCC STATEMENT
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
This telephone complies with Part 68
of FCC Rules. You must, upon re-
quest, provide the FCC Registration
Number and the REN to your phone
company. These numbers are shown
on the bottom of the base.
This symbol is intended to alert you
to the presence of uninsulated dan-
gerous voltage within the product’s
enclosure that might be of sufficient
magnitude to constitute a risk of
electric shock. Do not open the
product’s case.
Note: You must not connect your
phone to any of the following:
• coin-operated systems
• party-line systems
This symbol is intended to inform
you that important operating and
!
maintenance instructions are in-
cluded in the literature accompany-
ing this product.
• most electronic key phone sys-
tems
3
43-1051.fm Page 4 Tuesday, August 17, 1999 1:08 PM
CONTENTS
Installation ............................................................................................................ 5
Installing the Handset’s Antenna ..................................................................... 5
Selecting a Location ........................................................................................ 5
Placing the Base on a Desk Top ............................................................... 6
Mounting the Base on a Wall Plate ........................................................... 6
Mounting the Base Directly on the Wall .................................................... 8
Connecting and Charging the Battery Pack .................................................... 9
Setting the Dialing Mode ............................................................................... 11
Turning the Ringer On or Off ......................................................................... 11
Setting the Volume ........................................................................................ 11
Operation ............................................................................................................ 12
Making and Receiving Calls .......................................................................... 12
Changing the Channel ................................................................................... 12
Using Redial .................................................................................................. 12
Using Flash .................................................................................................... 13
Using Tone Services on a Pulse Line ............................................................ 13
Paging ........................................................................................................... 14
Memory Dialing .............................................................................................. 14
Storing a Number in Memory .................................................................. 14
Entering a Pause .................................................................................... 15
Dialing a Memory Number ...................................................................... 15
Chain-Dialing Service Numbers .............................................................. 15
Testing Stored Emergency Numbers ...................................................... 15
Troubleshooting ................................................................................................. 16
Care and Maintenance ....................................................................................... 18
Replacing the Battery Pack ........................................................................... 19
The FCC Wants You to Know ........................................................................ 20
Lightning ........................................................................................................ 21
4
43-1051.fm Page 5 Tuesday, August 17, 1999 1:08 PM
INSTALLATION
SELECTING A
LOCATION
INSTALLING THE
HANDSET’S ANTENNA
You can place the phone on a desk top
or table, or mount it on a wall. Select a
location that is:
Insert the antenna into the hole at the
top of the handset, then rotate the an-
tenna clockwise until it is secure.
• Near an AC outlet
• Near a telephone line jack
• Out of the way of normal activities
• Away from electrical machinery,
electrical appliances, metal walls
or filing cabinets, wireless inter-
coms, alarms, and room monitors
• Away from other cordless phones
FLASH
TALK
The base’s location affects the hand-
set’s range. If you have a choice of
several locations, try each to see
which provides the best performance.
REDIAL
MEMORY CHANNEL
ABC
DEF
1
GHI
2
3
MNO
JKL
4
PQRS
5
TUV
6
WXYZ
7
8
OPER
9
0
LOW BATT
Caution: The supplied RadioShack
adapter was designed specifically for
your ET-551. Use only the supplied
adapter.
25
CHANNEL
RadioShack
Notes:
• Your telephone connects directly
to a modular telephone line jack. If
your phone line jack is not a mod-
ular jack, you can update the wir-
ing yourself, using jacks and
adapters available at your local
RadioShack store. Or, you can let
the phone company update the
wiring for you.
• The USOC number of the jack to
be installed is RJ11C (RJ11W if
you want to mount it on a wall
plate).
5
43-1051.fm Page 6 Tuesday, August 17, 1999 1:08 PM
4. Plug the adapter into a standard
AC outlet.
Placing the Base
on a Desk Top
Follow these steps when you place
the base on a desk, shelf, or table.
1. Plug one end of the supplied long
modular cord into the LINE jack on
the back of the base.
5. Plug the modular cord’s other end
into a modular phone line jack.
LINE
12V
DC
P
T
2. Insert
the
supplied
power
adapter’s barrel plug into the DC
12V jack on the back of the base.
6. Fully extend the base’s antenna
and place it in a vertical position.
Mounting the Base
on a Wall Plate
LINE
12V
DC
P
T
1. Plug one end of the supplied short
modular cord into the LINE jack on
the back of the base.
3. Route the adapter’s cord through
the strain relief slot on top of the
base.
Strain Relief Slot
LINE
12V
DC
P
T
6
43-1051.fm Page 7 Tuesday, August 17, 1999 1:08 PM
2. Insert
the
supplied
power
4. Plug the adapter into a standard
AC outlet.
adapter’s barrel plug into the DC
12V jack on the back of the base.
LINE
12V
DC
P
T
5. Plug the short modular cord’s
other end into the wall plate jack,
then align the base’s keyhole slots
with the wall plate studs and slide
the base downward to secure it.
3. Route the modular cord through
the groove on the bottom of the
base and the adapter cord
through the strain relief slot on top
of the base.
Strain Relief Slot
LINE
O F F
R I N G E R
Groove
O N
6. Fully extend the base’s antenna
and place it in a vertical position.
7
43-1051.fm Page 8 Tuesday, August 17, 1999 1:08 PM
4. Route the adapter’s cord through
the strain relief slot on top of the
base.
Mounting the Base
Directly on the Wall
For this mounting method, you need
two wood screws (not supplied) with
heads that fit into the keyhole slots on
the bottom of the base.
Strain Relief Slot
1. Drill two holes 315/16
inches apart. Then
thread a screw into
5. Align the keyhole slots with the
mounting screws and slide the
base downward to secure it.
315
each hole, letting
the heads extend
/16
5
about /16 inch from
5/16
the wall.
LINE
2. Plug one end of the supplied short
modular cord into the LINE jack on
the back of the base.
O F F
R I N G E R
O N
LINE
12V
DC
P
T
6. Plug the adapter into a standard
AC outlet.
3. Insert
the
supplied
power
adapter’s barrel plug into the DC
12V jack on the back of the base.
LINE
12V
DC
P
T
8
43-1051.fm Page 9 Tuesday, August 17, 1999 1:08 PM
7. Plug the cord’s other end into a
modular phone line jack.
CONNECTING AND
CHARGING THE
BATTERY PACK
The ET-551 comes with a recharge-
able nickel-cadmium battery pack. Be-
fore using your phone, you must
connect the battery pack then charge
it for about 24 hours.
Follow these steps to charge the bat-
tery pack.
8. Fully extend the base’s antenna
and place it in a vertical position.
1. Press down and slide off the
handset’s battery compartment
cover as shown.
2. Insert the battery pack’s connec-
tor into the phone’s socket. The
plug fits only one way.
3. Replace the cover.
9
43-1051.fm Page 10 Tuesday, August 17, 1999 1:08 PM
4. To charge the battery pack, simply
place the handset on the base.
If this happens, return the handset
to the base for a few seconds.
• If the LOW BATT indicator does
not light, but the phone does not
work, recharge the battery pack.
The battery voltage might be too
low to light the indicator.
Charge
Indicator
• If the battery pack gets weak dur-
ing a call, the handset sounds
three beeps every 30 seconds,
and the LOW BATT indicator flash-
es for 2 minutes. After 2 minutes,
the phone automatically discon-
nects. If this happens, you cannot
make another call on the phone
until you recharge the battery
pack.
OFF
RINGER
ON
The CHARGE indicator on the
base lights.
• About every 30 days, fully dis-
charge the battery pack by keep-
ing the handset off the base until
the LOW BATT indicator lights.
Otherwise, the battery pack loses
its ability to fully recharge.
Recharge the battery pack when the
LOW BATT indicator on the handset
flashes.
8
OPER
7
9
• Using a pencil eraser, clean the
charging contacts on the handset
and the base about once a month
to make sure they are not dirty or
tarnished.
0
LOW BATT
Notes:
• If the CHARGE indicator does not
light when you place the handset
on the base, be sure the battery
pack and AC adapter are correctly
and securely connected.
• When you first use the phone after
charging or recharging the battery
pack, the phone might not work
and you might hear an error tone.
10
43-1051.fm Page 11 Tuesday, August 17, 1999 1:08 PM
• If the battery pack gets completely
discharged, the ET-551 loses the
security access-protection code.
To reset the code, place the hand-
set on the base and charge the
battery pack.
If the dial tone stops, you have
T/P
T
to .
touch-tone service. Leave
set
If the dial tone continues, you
T/P
P
to .
have pulse service. Set
• The supplied battery pack should
last about a year. When the bat-
tery pack loses its ability to fully
recharge, order a replacement
battery pack from your local Ra-
dioShack store (see “Replacing
the Battery Pack” on Page 19).
TURNING THE RINGER
ON OR OFF
RINGER
To turn off the ringer, set
on
OFF
the base to
ON
. To turn on the ringer,
set it to
.
SETTING THE DIALING
MODE
T/P
Set
(Tone/Pulse) on the back of
the base for the type of service you
have. If you are not sure which type
you have, do this test.
Note: With the base’s ringer off, you
can still make calls using the phone.
You can also receive calls if you hear
another telephone on the same line
ringing.
LIE
DV
T
P
SETTING THE VOLUME
T/P
T
to .
1. Set
VOLUME
Adjust
on the side of the
handset to control the volume of the
sound you hear through the handset.
TALK
2. Lift the handset, press
listen for a dial tone.
, and
0
3. Press any number other than .
VOLUME
LO
HI
Note: If your phone system
requires that you dial an access
9
code ( , for example) before you
dial an outside number, do not
press the access code either.
11
43-1051.fm Page 12 Tuesday, August 17, 1999 1:08 PM
OPERATION
MAKING AND
RECEIVING CALLS
CHANGING THE
CHANNEL
To make a call, pick up the handset
and press TALK. When the TALK indi-
cator lights steadily and you hear the
dial tone, dial the phone number.
The ET-551 finds a clear channel for
each call, but if you notice interference
during a call, you can press CHANNEL
to find a clearer channel.
FLASH
To answer a call if the handset is on
the base, simply lift the handset and
begin your conversation.
TALK
CHANNEL
REDIAL
MEMORY
DEF
ABC
To answer a call if the handset is not
on the base, press TALK on the hand-
set before speaking.
1
2
3
The ET-551 changes to a different
channel each time you press CHAN-
NEL.
FLASH
TALK
REDIAL
CHANNEL
MEMORY
Note: If the handset is too far from the
base, the channel might not change.
Move closer to the base and try again.
DEF
ABC
1
2
3
To end a call, place the handset on the
base or press TALK.
USING REDIAL
TALK to hang up
Note: If you press
REDIAL lets you quickly dial the last
number dialed. When you hear the dial
tone after pressing TALK, simply press
REDIAL.
and the phone does not disconnect,
place the handset on the base or press
TALK again while holding the handset
closer to the base.
FLASH
TALK
CHANNEL
REDIAL
MEMORY
DEF
ABC
1
2
3
Note: The redial memory does not
store a flash entry (see “Using Flash”
on Page 13).
12
43-1051.fm Page 13 Tuesday, August 17, 1999 1:08 PM
USING FLASH
USING TONE SERVICES
ON A PULSE LINE
FLASH
performs the electronic equiva-
lent of a switchhook operation for spe-
cial services, such as Call Waiting.
Some special services, such as bank-
by-phone, require tone signals. If you
have pulse service, you can still use
these special tone services by follow-
ing these steps.
FLASH
TALK
CHANNEL
REDIAL
MEMORY
T/P
P
1. Be sure
is set to .
DEF
ABC
TALK
2. Press
.
1
2
3
3. When you hear the dial tone, dial
the service’s main number.
For example, if you have Call Waiting,
FLASH
call without disconnecting the current
4. When you want to send tone sig-
press
to answer an incoming
nals, press
. Any additional
numbers you dial are sent as tone
signals.
FLASH
call. Press
first call.
again to return to the
Note: If you do not have any special
FLASH
8
OPER
7
9
phone services, pressing
disconnect the current call.
might
0
LOW BATT
5. After you complete the call, return
the handset to the base or press
TALK
. The phone automatically
resets to the pulse mode.
13
43-1051.fm Page 14 Tuesday, August 17, 1999 1:08 PM
PAGING
MEMORY DIALING
To page the person who has the hand-
set or to locate the handset when the
You can store up to 16 digits in each of
the ten memory locations, then dial a
stored number by pressing a one-digit
memory location number.
PAGE
phone is not in use, press
base. The handset beeps three times.
PAGE
on the
If you hold down
for 2 seconds,
the handset beeps for 30 seconds to
give you time to locate the handset.
Storing a Number in Memory
Note: An error tone sounds and the
phone exits the programming mode if
you wait more than about 6 seconds
between each key press or enter more
than 16 digits.
AGE
P
RadioShack
CHANNEL
CHARGE
1
2
3
4
OFF
5
6
MEMORY
1. Press
. The TALK indica-
RINGER
7
8
9
ON
tor flashes.
FLASH
TALK
REDIAL
CHANNEL
MEMORY
DEF
ABC
1
2
3
2. Enter the phone number and any
tone and pause entries (see
“Using Tone Services on a Pulse
Line” on Page 13 and “Entering a
Pause” on Page 15).
Note: Each tone or pause entry
uses one digit of memory.
MEMORY
, then enter the
3. Press
0 9
memory location number ( – ). A
single tone sounds to indicate that
the number is stored.
Repeat Steps 2–4 for each num-
ber you want to store.
14
43-1051.fm Page 15 Tuesday, August 17, 1999 1:08 PM
Note: If three quick beeps sound,
you have made an error and the
number was not stored. Start
again from Step 2.
Dialing a Memory Number
To dial a number stored in memory,
TALK
tone, press
press
. When you hear a dial
MEMORY
and enter the
For each stored number, write the per-
son’s or company’s name next to the
appropriate location number on the
memory dialing card. We recommend
you use a pencil in case you want to
change the number later.
memory location number for the num-
ber you want to dial.
Chain-Dialing Service
Numbers
Memory
When calling special services (such as
alternate long distance or bank by
phone), dial the service’s main number
first. Then, at the appropriate place in
Dialing Card
RadioShack
25
CHANNEL
CHARGE
1
2
3
4
5
OFF
6
7
RINGER
8
9
MEMORY
the call, press
then the num-
ON
0
ber for the location where the addition-
al information is stored.
Testing Stored Emergency
Numbers
To erase a stored number, simply
store a new number in its place.
If you store an emergency service’s
number (police department, fire de-
partment, ambulance) and you choose
to test the stored number, make the
test call during the late evening or early
morning hours to avoid peak demand
periods. Also, remain on the line to ex-
plain the reason for your call.
Entering a Pause
In some telephone systems, you must
dial an access code ( , for example)
9
and wait for a second dial tone before
you can dial an outside number. You
can store the access code with the
phone number. However, you should
also store a pause after the access
code to allow the outside line time to
connect.
REDIAL
To do so, press
at the appro-
priate place to enter a 4-second pause.
REDIAL
For a longer pause, press
ditional times.
ad-
15
43-1051.fm Page 16 Tuesday, August 17, 1999 1:08 PM
TROUBLESHOOTING
We do not expect you to have any problems with your phone, but if you do, the fol-
lowing suggestions might help.
Problem
Suggestion
Low volume or unusual
sounds.
Someone has picked up another phone on the
same line. Hang up the other phone.
Press CHANNEL to change the channel.
Adjust the handset’s volume.
Severe noise interference.
Press CHANNEL to change the channel.
Keep the handset away from computers, re-
mote control toys, wireless microphones, alarm
systems, intercoms, room monitors, fluorescent
lights, and electrical appliances.
Move to another location or turn off the source
of the interference.
The phone cannot be operated Fully extend the base’s antenna in a vertical po-
at a useful distance from the
base because the signal be-
comes weak or noisy (hand-
set’s range has decreased).
sition.
Be sure neither antenna is touching a metal sur-
face.
Return the handset to the base to recharge the
battery pack.
The phone does not work or
works poorly.
Be sure the base’s phone line cord and AC
adapter are correctly and securely connected,
and the battery pack is charged.
The handset battery pack does Check the charging contacts on the handset
not charge.
and base. If they are dirty, clean them with a
pencil eraser.
Be sure the battery pack is connected correctly.
Replace the battery pack.
16
43-1051.fm Page 17 Tuesday, August 17, 1999 1:08 PM
Problem
Suggestion
The handset does not ring or
receive a page.
The battery pack might be weak. Charge the
battery pack.
Extend the base’s antenna vertically.
Move the handset closer to the base.
Move the base away from other electrical devic-
es and sources of noise.
The handset stops working or
works poorly during a call.
Move the handset closer to the base.
Fully extend the base’s antenna, and place it in
a vertical position.
Check the charging contacts on the handset
and base. If they are dirty, clean them with a
pencil eraser.
Be sure the handset’s battery pack is charged.
(If the battery power is too low, it does not have
enough power to light the LOW BATT indicator.)
If the base loses power while the handset is off
of it, the security access-protection code might
change. Restore power to the base, then place
the handset back on the base. The CHARGE in-
dicator lights when the code is reset.
The call is too noisy.
Change channels or hang up and redial the
number.
If you still have problems, disconnect the phone. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the prob-
lem, take your phone to your local RadioShack store for assistance.
17
43-1051.fm Page 18 Tuesday, August 17, 1999 1:08 PM
CARE AND MAINTENANCE
Your RadioShack ET-551 25-Channel Cordless Phone with 10-Number Memory is
an example of superior design and craftsmanship. The following suggestions will
help you care for your cordless phone so you can enjoy it for years.
Keep the phone dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Handle the phone gently and carefully. Dropping it can damage cir-
cuit boards and cases and can cause the phone to work improperly.
Use and store the phone only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices,
damage batteries, and distort or melt plastic parts.
Keep the phone away from dust and dirt, which can cause premature
wear of parts.
Wipe the phone with a damp cloth occasionally to keep it looking
new. Do not use harsh chemicals, cleaning solvents, or strong deter-
gents to clean the phone.
Modifying or tampering with the phone’s internal components can cause a malfunc-
tion and might invalidate your phone’s warranty and void your FCC authorization to
operate it. If your phone is not performing as it should, take it to your local Ra-
dioShack store for assistance. If the trouble is affecting the phone lines, the phone
company might ask you to disconnect your phone until you have resolved the prob-
lem.
18
43-1051.fm Page 19 Tuesday, August 17, 1999 1:08 PM
2. Gently pull out the battery connec-
tor to disconnect it, then remove
the battery pack.
REPLACING THE
BATTERY PACK
If you follow the instructions in “Con-
necting and Charging the Battery
Pack” on Page 9, the battery pack
should last about one year. If the bat-
tery pack will not hold a charge for
more than 2 hours after an overnight
charge, replace it with a new 3.6 V,
300 mAh battery pack with a connector
that fits the socket in the battery com-
partment. You can order a replace-
ment battery pack through your local
RadioShack store.
3. Insert a fresh battery pack and
insert its connector into the socket
inside the battery compartment.
Install the new battery pack as de-
scribed here, then charge the battery
pack (see “Connecting and Charging
the Battery Pack” on Page 9).
4. Replace the cover.
Cautions:
• You must use a replacement bat-
tery pack of the same size and
type.
Note: To avoid losing phone numbers
stored in memory, try to install and be-
gin charging the new battery pack
within about 2 minutes.
• Do not dispose of the battery pack
in a fire because it might explode.
1. Press down and slide off the
handset’s battery compartment
cover as shown.
• Do not open or mutilate the bat-
tery pack.
• Be careful not to short the battery
pack by touching it with conduct-
ing materials, such as rings,
bracelets, and keys. The battery
pack or conductor might overheat
and burn.
19
43-1051.fm Page 20 Tuesday, August 17, 1999 1:08 PM
Important: This phone contains a re-
chargeable nickel-cadmium battery
pack. At the end of the battery pack’s
useful life, it must be recycled or dis-
posed of properly. Contact your local,
county, or state hazardous waste man-
agement authorities for information on
recycling or disposal programs in your
area. Some options that might be
available are: municipal curb-side col-
lection, drop-off boxes at retailers such
as your local RadioShack store, recy-
cling collection centers, and mail-back
programs.
Your phone might cause TV or radio
interference even when it is operating
properly. To determine whether your
phone is causing the interference, turn
off your phone. If the interference goes
away, your phone is causing the inter-
ference.
Try to eliminate the interference by:
• Moving your phone away from the
receiver
• Connecting your phone to an AC
outlet that is on a different electri-
cal circuit from the receiver
• Contacting
dioShack store for help
your
local
Ra-
THE FCC WANTS YOU
TO KNOW
If you cannot eliminate the interfer-
ence, the FCC requires that you stop
using your phone.
In the unlikely event that your phone
causes problems on the phone line,
the phone company can temporarily
discontinue your service. If this hap-
pens, the phone company attempts to
notify you in advance. If advance no-
tice is not practical, the phone compa-
ny notifies you as soon as possible and
advises you of your right to file a com-
plaint with the FCC.
Some cordless phones operate at fre-
quencies that might cause interference
to nearby TVs and VCRs. To minimize
or prevent such interference, the base
of the cordless phone should not be
placed near or on top of a TV or VCR.
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect
the operation of this telephone. The
telephone company notifies you of
these changes in advance, so you can
take the necessary steps to prevent in-
terruption of your telephone service.
20
43-1051.fm Page 21 Tuesday, August 17, 1999 1:08 PM
LIGHTNING
Your telephone has built-in lightning
protection to reduce the risk of damage
from surges in telephone line and pow-
er line current. This lightning protection
meets or exceeds FCC requirements.
However, lightning striking the tele-
phone or power lines can damage your
telephone.
Lightning damage is not common.
Nevertheless, if you live in an area that
has severe electrical storms, we sug-
gest you unplug your phone during
storms to reduce the possibility of
damage.
21
43-1051.fm Page 22 Tuesday, August 17, 1999 1:08 PM
NOTES
22
43-1051.fm Page 23 Tuesday, August 17, 1999 1:08 PM
23
43-1051.fm Page 24 Tuesday, August 17, 1999 1:08 PM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
8A7
Printed in China
|